Sodium-ion vs lithium-ion in 2026: what changes when your prototype switches chemistry
For founders and engineers building battery-powered products, especially cold-weather outdoor gear, backup power, and IoT devices. Sodium-ion moved from the lab to GWh-scale production this year. Here is where it fits, what it changes in the electronics and firmware, and what to test before you commit.
November 17, 20267 min read

Written by Konstantin Dolgan, Ph.D., NPDP
Founder & CEO, Product Development Engineer
Published November 17, 2026

What changed in 2026
Cells reached volume. On February 5, 2026, CATL and Changan unveiled what they call the world's first mass-production passenger vehicle with sodium-ion batteries, with CATL's Naxtra cells rated up to 175 Wh/kg (CATL).
At its April 2026 Super Tech Day, CATL said Naxtra had reached GWh-level industrialization and would enter full-scale mass production by the end of 2026, and it is adding 40 GWh of annual sodium-ion capacity in Fujian (Electric & Hybrid Vehicle Technology International).
CATL also signed a three-year, 60 GWh sodium-ion supply agreement with storage integrator HyperStrong (Battery Technology).
Consumer products exist. BLUETTI sells the Pioneer Na, a 900 Wh sodium-ion portable power station. The maker rates it to charge at -15 °C (5 °F), to discharge down to -25 °C (-13 °F), and for 4,000+ cycles (BLUETTI). Those are manufacturer claims, but they show the pitch: cold-weather reliability.
The US supply base is thin. Natron Energy, a US sodium-ion cell maker, ceased operations on September 3, 2025, after funding problems (IEEE Spectrum).
Peak Energy announced in July 2026 a Sacramento factory for sodium-ion grid storage packs, with first products in early 2027 (Los Angeles Times), and its cells come from Chinese manufacturers built to its specification (Renewability).
For a US product team, that means sample cells in 2026 will most likely come from overseas makers.
Where sodium-ion fits in a product, and where it does not
The Faraday Institution frames sodium-ion as most attractive where lifetime cost, not weight or volume, is the deciding factor, and as a competitor mainly to LFP and lead-acid (Faraday Institution, Insight 11).
Product need | Leans sodium-ion | Leans lithium-ion | What the prototype must prove |
|---|---|---|---|
Works in hard cold (hunting, ice fishing, winter trail cameras, outdoor sensors) | Yes, if the cell's datasheet supports your low-temperature charge and discharge | Lithium-ion may need heaters or insulation for charging in the cold | Cold-chamber charge and discharge at your real temperatures and loads |
Smallest, lightest pack (wearables, handhelds, drones) | Usually not; check the datasheet's energy density | Yes, still the default for tight space and weight | Runtime per gram and per cubic centimeter in the actual enclosure |
Backup or stationary power (home backup, off-grid, base stations) | Strong candidate; weight matters less | LFP is the usual comparison | Cycle life and standby loss at your duty cycle |
Replacing a lead-acid battery | Strong candidate | LFP is the other option | Charger compatibility and voltage window at the system level |
Must ship by air often (samples, spares) | Class 9, with its own UN numbers (UN 3551, UN 3552) | Class 9 (UN 3480, UN 3481) | Packaging, state of charge, and UN 38.3 test summary in hand |
If your product spends January in a deer stand, sodium-ion deserves a test build. If it lives in a pocket, lithium-ion is probably still the right call in 2026.
What changes in the electronics and firmware
A sodium-ion cell is not a lithium-ion cell with a different label. The voltage window differs, and that touches several parts of the design.
End-of-discharge voltage. The new UL 2743 edition for portable power packs uses an end-of-discharge voltage of 1.5 V per cell for sodium-ion, against 2.5 V per cell for lithium-ion, unless the cell maker specifies otherwise (Intertek Standards Update Notice, UL 2743, March 18, 2026).
In practice, that means your low-voltage cutoff, your boost or buck converter's minimum input, and any brown-out logic need to be set from the sodium-ion datasheet, not carried over from a lithium-ion design.
Charging. The same standard requires that charging a lithium-ion or sodium-ion battery under normal conditions stays within the cell's specified operating region. Check that your charger and protection ICs can be set to the cell maker's sodium-ion voltage, current, and temperature limits. A part fixed to lithium-ion thresholds will not fit.
State of charge and the fuel gauge. Because the voltage window differs, a fuel-gauge table built for lithium-ion cells will not match a sodium-ion cell. If your product shows a battery percentage, plan a calibration pass on real cells, at real temperatures. This is where firmware testing and a simple test fixture pay for themselves.
Thermal and mechanical. Cold-weather products move the hard problems to the enclosure: condensation, seals, and how the pack is held and connected at low temperature. See enclosure design for electronics and our outdoor electronics prototype cost guide for the sealing and battery-life side of those builds.
Where AI and simulation help
AI and simulation will not choose the chemistry, but they shorten the loop: a thermal model can screen pack layouts and cold-soak cases before you build, and a data-driven state-of-charge model can be fitted to your own bench logs instead of a generic lithium-ion table. Either is only as good as the measurements behind it. See physics AI simulation in prototyping.
Certification and shipping: sodium-ion has its own entries
Transport. The IATA 2026 battery guidance classifies sodium-ion cells and batteries with organic electrolyte as Class 9 dangerous goods: UN 3551 when shipped alone, and UN 3552 when packed with or contained in equipment.
All cells and batteries must pass the UN Manual of Tests and Criteria, Part III, sub-section 38.3 (UN 38.3), and standalone sodium-ion cells and batteries are limited to a maximum 30% state of charge and are forbidden on passenger aircraft.
For sodium-ion batteries packed with or in equipment, IATA recommends shipping at no more than 30% state of charge (IATA Lithium and Sodium Ion Battery Guidance, 2026). Plan for this before you mail prototype packs to a test house or beta tester.
Product safety. The 2025 third edition of ANSI/CAN/UL 2743 for portable power packs adds sodium-ion batteries and requires sodium-ion cells to comply with UL/ULC 2580 or UL 1973.
Intertek lists September 24, 2027 as the date by which products certified to UL 2743 must move to the third edition (Intertek SUN, March 18, 2026).
Other product categories may still reference lithium-focused standards, so ask your test lab early which standard and which cell certification it will accept for a sodium-ion pack.
For lithium-side rules that may also apply to your product, see our posts on the CPSC lithium battery rule for micromobility and the EU replaceable battery rule.
Sodium-ion battery design checklist for a 2026 prototype
- Write down the real operating and charging temperatures, the runtime target, and the size and weight budget before picking a chemistry.
- Get the cell datasheet, the UN 38.3 test summary, and the cell safety certification (for example UL 1973 or UL/ULC 2580, if your target standard calls for it) before designing the pack.
- Set the low-voltage cutoff, converter minimum input, and brown-out thresholds from the sodium-ion datasheet.
- Confirm the charger and protection ICs can follow the cell maker's charge voltage, current, and temperature limits.
- Plan a state-of-charge calibration on real cells at cold, room, and hot temperatures.
- Run cold-chamber charge and discharge tests at your actual loads, then a beta test in the real environment.
- If the call is close, build one lithium-ion (or LFP) control prototype and compare data, not brochures.
- Plan transport early: UN 3551 or UN 3552, state of charge, packaging, and the battery mark.
- Ask your test lab which safety standard it will apply and when.
How we approach a chemistry decision
For a battery-powered product, chemistry is one of the early risks we look at, alongside the electronics, firmware, and enclosure.
Stage 1, Review/Analysis + Plan, is a fixed $800 single payment: a technical feasibility analysis, the key risks (such as chemistry, temperature range, and certification), and a staged plan with the recommended next step. Stage 1 cost estimates use publicly available prices.
Then electronic design and prototyping turn the decision into a test build.
See the process map, typical product development cost by complexity, and our outdoor and hunting product development work.
Weighing sodium-ion for a new product?
If you are weighing sodium-ion for a new product, you can book a free 20-min call with an engineer.
Sources
Frequently asked questions
Is sodium-ion better than lithium-ion?
Not across the board. Sodium-ion's strengths are cold performance, safety margin, and potentially lower cost at scale; CATL rates its Naxtra cells at up to 175 Wh/kg, which it compares to LFP. Lithium-ion remains the default for the smallest, lightest packs. The choice depends on temperature range, size and weight budget, and duty cycle.
Can I swap lithium-ion cells for sodium-ion cells in my existing design?
Usually not without changes. UL 2743 (2025 edition) uses an end-of-discharge voltage of 1.5 V per cell for sodium-ion versus 2.5 V for lithium-ion, unless the cell maker specifies otherwise. Charger settings, low-voltage cutoff, converter input range, and fuel-gauge calibration must be checked against the sodium-ion datasheet.
Do sodium-ion batteries work in cold weather?
That is their main selling point. CATL reports over 90% capacity retention at -40 °C for Naxtra cells, and BLUETTI rates its Pioneer Na to charge at -15 °C and discharge at -25 °C. These are manufacturer figures, so test your prototype in a cold chamber at real loads.
How do I ship sodium-ion prototype batteries?
As Class 9 dangerous goods: UN 3551 alone, UN 3552 packed with or in equipment, after passing UN 38.3. Under IATA's 2026 guidance, standalone sodium-ion batteries ship at no more than 30% state of charge and not on passenger aircraft; 30% or less is recommended for batteries in or with equipment.
What does it cost to start a sodium-ion product with LA NPDT?
Stage 1, Review/Analysis + Plan, is a fixed $800 single payment: a technical feasibility analysis, the key risks, and a staged plan with the recommended next step. Typical later-stage costs by complexity are on the product development cost page, or book a free 20-min call first.
Tagged:AIElectronicsPrototyping
Services related to this guide
- Best product development companiesHow the leading US firms compare, and which one fits your stage and budget.
- Best product design companiesDesign studios compared by scope, industry and what they hand off.
- Product engineering companiesEngineering firms for physical products compared by discipline, rigor and budget.
- Consultant vs firm vs freelancerWhat each option costs, what it delivers and where to find them.



